- fix naming and formatting
- provide more context when erroring auth
- do not capitalize errors
- fix wrong documentation
- remove ugly remoteError{}
Signed-off-by: Antonio Murdaca <runcom@redhat.com>
If we detect a Docker-Distribution-Api-Version header indicating that
the registry speaks the V2 protocol, no fallback to V1 should take
place.
The same applies if a V2 registry operation succeeds while attempting a
push or pull.
Signed-off-by: Aaron Lehmann <aaron.lehmann@docker.com>
/dev/sda wasn't an invalid device and this test failed, so, hopefully
/dev/sdX isn't going to exist in other envs.
Signed-off-by: Christy Perez <christy@linux.vnet.ibm.com>
These filters are only use to interchange data between clients and daemons.
They don't belong to the parsers package.
Signed-off-by: David Calavera <david.calavera@gmail.com>
- Move time json marshaling to the jsonlog package: this is a docker
internal hack that we should not promote as a library.
- Move Timestamp encoding/decoding functions to the API types: This is
only used there. It could be a standalone library but I don't this
it's worth having a separated repo for this. It could introduce more
complexity than it solves.
Signed-off-by: David Calavera <david.calavera@gmail.com>
After addition of multi-host networking in Docker 1.9, Docker Remote
API is still returning only the network specified during creation
of the container in the “List Containers” (`/containers/json`) endpoint:
...
"HostConfig": {
"NetworkMode": "default"
},
The list of networks containers are attached to is only available at
Get Container (`/containers/<id>/json`) endpoint.
This does not allow applications utilizing multi-host networking to
be built on top of Docker Remote API.
Therefore I added a simple `"NetworkSettings"` section to the
`/containers/json` endpoint. This is not identical to the NetworkSettings
returned in Get Container (`/containers/<id>/json`) endpoint. It only
contains a single field `"Networks"`, which is essentially the same
value shown in inspect output of a container.
This change adds the following section to the `/containers/json`:
"NetworkSettings": {
"Networks": {
"bridge": {
"EndpointID": "2cdc4edb1ded3631c81f57966563e...",
"Gateway": "172.17.0.1",
"IPAddress": "172.17.0.2",
"IPPrefixLen": 16,
"IPv6Gateway": "",
"GlobalIPv6Address": "",
"GlobalIPv6PrefixLen": 0,
"MacAddress": "02:42:ac:11:00:02"
}
}
}
This is of type `SummaryNetworkSettings` type, a minimal version of
`api/types#NetworkSettings`.
Actually all I need is the network name and the IPAddress fields. If folks
find this addition too big, I can create a `SummaryEndpointSettings` field
as well, containing just the IPAddress field.
Signed-off-by: Ahmet Alp Balkan <ahmetalpbalkan@gmail.com>
To make docker inspect return a consistent result of networksettings
for created container and stopped container, it's bettew to update
the network settings on container creating.
Signed-off-by: Lei Jitang <leijitang@huawei.com>
This commit adds a transfer manager which deduplicates and schedules
transfers, and also an upload manager and download manager that build on
top of the transfer manager to provide high-level interfaces for uploads
and downloads. The push and pull code is modified to use these building
blocks.
Some benefits of the changes:
- Simplification of push/pull code
- Pushes can upload layers concurrently
- Failed downloads and uploads are retried after backoff delays
- Cancellation is supported, but individual transfers will only be
cancelled if all pushes or pulls using them are cancelled.
- The distribution code is decoupled from Docker Engine packages and API
conventions (i.e. streamformatter), which will make it easier to split
out.
This commit also includes unit tests for the new distribution/xfer
package. The tests cover 87.8% of the statements in the package.
Signed-off-by: Aaron Lehmann <aaron.lehmann@docker.com>
It makes the behavior completely consistent across commands.
It adds tests to check that execution stops when an element is not
found.
Signed-off-by: David Calavera <david.calavera@gmail.com>
This test was directly comparing lines of output from "docker images".
Sometimes, when busybox had been pushed to the hub recently, the
relative creation times would differ like this:
... obtained []string = []string{"busybox", "latest", "d9551b4026f0", "27", "minutes", "ago", "1.113", "MB"}
... expected []string = []string{"busybox", "latest", "d9551b4026f0", "26", "minutes", "ago", "1.113", "MB"}
Fixing by removing the time-since-creation fields from the comparison.
Signed-off-by: Aaron Lehmann <aaron.lehmann@docker.com>
Each plug-in operates as a separate service, and registers with Docker
through general (plug-ins API)
[https://blog.docker.com/2015/06/extending-docker-with-plugins/]. No
Docker daemon recompilation is required in order to add / remove an
authentication plug-in. Each plug-in is notified twice for each
operation: 1) before the operation is performed and, 2) before the
response is returned to the client. The plug-ins can modify the response
that is returned to the client.
The authorization depends on the authorization effort that takes place
in parallel [https://github.com/docker/docker/issues/13697].
This is the official issue of the authorization effort:
https://github.com/docker/docker/issues/14674
(Here)[https://github.com/rhatdan/docker-rbac] you can find an open
document that discusses a default RBAC plug-in for Docker.
Signed-off-by: Liron Levin <liron@twistlock.com>
Added container create flow test and extended the verification for ps
Since seccomp is still a configurable build-tag, add a requirements
entry for seccomp, as well as move seccomp tests to "_unix" given it
won't be applicable to other platforms at this time.
Docker-DCO-1.1-Signed-off-by: Phil Estes <estesp@linux.vnet.ibm.com> (github: estesp)
This test can fail if it is run close to a second boundary:
FAIL: docker_cli_logs_test.go:169: DockerSuite.TestLogsSince
docker_cli_logs_test.go:183:
c.Assert(out, checker.Not(checker.Contains), v,
check.Commentf("unexpected log message returned, since=%v", since))
... obtained string = "" +
... "2015-12-07T19:54:45.000551883Z 1449518084 log2\n" +
... "2015-12-07T19:54:47.001310929Z 1449518086 log3\n"
... substring string = "log2"
... unexpected log message returned, since=1449518085
The problem is that it generates log lines using date +%s and uses that
timestamp as a reference for log filtering with (--since) later on in
the test. However, the timestamp that date +%s generates may not match
the log timestamp.
This commit changes the test to parse the log timestamp itself instead
of relying on a parallel timestamp.
Signed-off-by: Aaron Lehmann <aaron.lehmann@docker.com>
